Keywords:

Car key chip

4

Magic Wand 4C 4D Transponder chip generator comes out, which not only generate 4D63, 83 40bit and 83 80bit chip but also is used to generate 4C chips original 4D70 blank Chip to 4D small capacity chips. Well, there is a detailed introduction of Magic Wand.

What is Magic Wand 4C 4D?
Power supply: Above 5v 1.5a usb charger, please charge the Magic Wand using
Android phone USB cable.
PS: You had better not use the sub-standard power supply because it will influence the function of magic wand ,leading to the magic WAND’s wrong.

6
4
Ford/Mazda immobilizer chips are 3 types available:
1. 4D63 (40bit/DST40) small capacity.
2. 83 (40bit/ DST40) small capacity.
3. 83 (80bit/DST80) big capacity.

 

a usages description of key button
Read
This button is used for reading chip. After you put the chip into the slot, press “Read” button and get the reading result. If it doesn’t succeed to read, the red indicator will continue flashing. While after reading successfully it will display, chip ID and the green indicator will keep flashing. At this time it is ready to copy, take out the chip and substitute the special chip for Magic WAND, press “Write” button and complete copying, after that it will display chip ID ,at the same time the green indicator will continue flashing, if it fails to copy, the red indicator will keep flashing.

Write ( This button is used to generate and copy chip)
Generate Chip: Put the chip into the slot , press the chip ID you want to generate, press “Write” button to get the results, the green indicator will keep flashing and display chip ID. In contrast, if the red indictor flashes it means reading is finished, maybe you put an error chip or the chip doesn’t match with the device.
Copy: you need to read out the chip ID before to copy, after it read out successfully you will get the chip ID, just press “Write” to finish copying. While if the red indicator flashes it means the chip doesn’t match with the device.

NOTES:when you add the key, you have to put the Magic Wand close to the ignition coil and the key go through the hole of Magic Wand, then follow the key programmer prompt to finish.
1.Put the original 4D70 blank chip into the chip slot.
2.Press the No. buttons 8 and 3, then press “Write” button, the green indicator will flash and means copy successfully.
3.Put the chip back into the key shell, then take it to the car to add key work together with key programmer.
8
What is Magic Wand 4C 4D function?
1: transform original 4D transponder into special
transponder(61.62.65.66.67.68…..)
2: Copy transponder (61.62.63.65.66.67.68)
4D Magic Wand is an progressive device for locksmith.
It not only work independently but work with handphone & computer.
Update constantly , work on special material.
It can settle many problems for locksmiths.
Magic Wand is needed by Beginner and exprienced locksmith.

Chip ID and the applicable car models
4C chip: old Toyota.  72G chip: Toyota G.  82G chip: Subaru G.  D68 chip: Daihatsu.  72DG: Daihatsu G. 60 chip: oldExcelle/ old Nissan/ old Mondeo. 61 chip: Mitsubishi. 62 chip: Subaru. 63 chip: Ford/Mazda. 64 chip: Chrysler/ Jeep. 65 chip: Suzuki. 66 chip: Suzuki. 67 chip: Toyota/Lexus. 68 chip: Toyota/Lexus. B9 chip Toyota Crown. 69 chip: Yamaha Motorcycle. 6A chip: Kawasaki Kawasaki. 6B chip: Suzuki Motorcycle.

 

2

I used this VMWare Workstation 12 on a Mac to successfully flash the PPK on a 2012 335xi e90 today. it shouldn’t be too hard to make it work with fusion I don’t think. ISTA/P 3.56.1.002 is working awesome! In a uncompressed VM size with ISTA/P is 280GB.
Note: have to run it in bootcamp until we can find a workaround for mac users

 

Very important reference!!

 

 

 

Here are some tips and ideas after i used this… Wish this helps.

 

Diagnostic tools can be used:
K+DCAN and ENET cables are supported for everything but MOST ring modules. For those, you will still need an ICOM emulator.

1 2

 

memory setting:

I would recommend anyone with less than 16gb of total host memory drop the VM memory down to 4gb or less.

 

connecting in either NAT or Bridge mode:

for use of an ICOM or ENET cable, you will need to use bridge mode. For general E9x and other K+DCAN vehicles, your network settings will not affect your ability to connect to the vehicle.

 

VMWare:

I chose VMWare because I feel like it’s the most stable and offers the most features. I may look into building a version with Virtualbox but at least for now, I’m going to stick with VMWare. I do however, want to get a mac to test with so that I can make sure I can get it working in Fusion as well as on PC. I think building an underlying linux host is a good idea, however, the idea behind this VM was simplicity and I feel like building it in this manner would be counter intuitive to that end goal.

 

Ublock instead of ABP:

I could install ublock origin instead of Ad Block Plus in Chrome to save some resources as well as speed it up a bit.

 

PDF Printer/CuteWriter:

Might be nice to have a PDF printer, like CutePDF pre-installed for “printing” from the various diagnostic tools.

 

Datens on the desktop:
I included these raw daten files in rar format for a reason. While they all are already loaded in NCSExpert, INPA, and the like. WinKFP deals best with one model series daten at a time. If you need to use WinKFP to program a module, extract that rar file and use the BMW coding tool to load it into WinKFP. There is a PDF in the help files folder on the desktop that illustrates how to use the coding tool to load the files into WinKFP. If you don’t plan on ever using WinKFP or programming some of these chassis codes you can go ahead and delete those or all of the datens.

 

Note:

All above is the customer solution. Try on your own risk.

Safe solution & easiest way is to avoid all installation problems, you can spend some dollars to buy BMW Rheingold software that has been installed on hard disk:

V2016.7 ISTA-D 3.55.31ISTA-P 3.59.0.600 Windows 7 HDD

V2016.3 ISTA-D 3.54.12 ISTA-P 3.58.0.500 Windows 8 HDD