Author Archives: Dương Nguyễn

5
Foxwell GT80 Plus is modern Windows 8.1 tablet computer, with 10 inch LED touch screen,Compatible with both OBDI and OBDII cars, SUVs, minivans, light-duty trucks sold worldwide from old to latest 2015, 2016 vehicles,Including AU Ford and Holden. Foxwell GT80 PLUS users manual download Foxwell GT80 Plus Highlights: 1. Update Online (free for 18months) 2. Support over 59 American, Asian and European vehicle makes around year 2015/2016 3. Communication interface: Built-in WIFI 802.11 b/g Wireless LAN USB 2.0 Bluetooth 4.0...
0 Comments | Posted By
8
Attention please. VW ETKA 7.5 electronic catalogue from China, especially from MUST be installed on Windows XP, NOT 64 bit system! Here is the how-to guide of ETKA 7.5 catalogue installation on Windows xp operation system. First, download ETKA 7.5 data and unzip in local disk D: Note: MUST unzip in disk D:; or it would not run in other disks 1.click on QQ:1 (select English and click on Next continuously until it completes) 2.copy LEXHDL5.DLL to local disk C:\windows\system...
0 Comments | Posted By
6
This is a turorial of how to use ENET Cable and E-sys interface to do coding on BMW i3. Equipment requirement: A laptop with Windows XP / WIN7 32 bit Software- E-sys Free download software: E-sys might come with the cables, but you can use with the newest version. E-Sys 3.26.1 Torrent full psdzdata 3.58.2.001 Coding tutorial: 1 – Computer to Car Connection The OBD-2 port on the i3 is located between the steering wheel and the driver door, under the steering...
0 Comments | Posted By
6
Disclaimer: Smart Key Teach-in only supports Mercedes-Benz Smart (1998~2002) with K-line protocol.   Smart Key Teach-in support ECU type as follows: MB – Smart vehicles dongle key programmer SMART Teach-in is required when keys are lost, damaged or if additional key is needed. Also, this procedure synchronizes engine ECU with BSI – can be used when changing damagedECU or BSI with new/used one! For adapting each remote with Immobilizer / BSI module the following dongle can be used: 1. Turn ignition ON without starting engine (position “1”). 2. Insert dongle in OBD connector (it is located under steering column, near pedals). 3. The LEDs must lit both, then green must blink few times. If all OK, green LED remains lit and red must be off. If  red LED blinks fast, this means an error, you may remove dongle and try again. 4. If red LED is off and green is on, turn OFF the ignition key. 5. Press twice LOCK button on each remote (if 3 button remote used) within 30 sec. Maximum of 4 keys can be programmed. 6. Turn ignition ON again, this completes learning sequence. Remote controls are working only when ignition is OFF, cranking is possible only when vehicle is in UNLOCK-ed state.  
0 Comments | Posted By
1
Here is a manual of how to read F series I-Step from VCM master, using BMW E-sys software.   The I-Level (aka I-Step) is the Integration Level of your car, which represents a package of firmwares for all your modules, and it corresponds to the version of ISTA/P last used to program your vehicle. To determine your I-Level, go to VCM Module => VCM Master Tab => click Read under I-Steps: The I-Step (current) is the one you want to...
0 Comments | Posted By
1
I used this VMWare Workstation 12 on a Mac to successfully flash the PPK on a 2012 335xi e90 today. it shouldn’t be too hard to make it work with fusion I don’t think. ISTA/P 3.56.1.002 is working awesome! In a uncompressed VM size with ISTA/P is 280GB. Note: have to run it in bootcamp until we can find a workaround for mac users   Very important reference!!       Here are some tips and ideas after i used...
0 Comments | Posted By
1
This is Audi J518 test cable available at obd2express.co.uk which has been verified to work well with VVDI commander, and VVDI Benz key programmer. Functions includes:   Work together with VVDI key programmer / VVDI MB BGA tool 2. Can do immobilizer online & component protection. 3. Can be used to connect J518 engine, gateway and instrument ignition switch     Audi J518 test cable in use: Audi J518 test cable package: Source:New J518 Test Line For AUDI Work With VVDI & VVDI MB BGA Tool
0 Comments | Posted By
1
iKeycutter CONDOR XC-MINI Master Series Automatic Key Cutting Machine is powerful and professional key cutting tool.it is easily operated,support online updating.Here is Steps on Ford key with Condor XC-MINI Cutting Machine. 1.Start your condor xc-mini key cutting machine,Power-On Password: 123456 2.Find the right key blade. 3.Insert it. 4.Check the menu and find the right car model. 5.Then it will shows the detailed tooth wear.Next,click enter. 6.Lean the key. 7.Insert new key blade,click the circle one to cut new blade.  
0 Comments | Posted By
8
Automatic V8/X6 Key Cutting Machine can make new keys without original key. Latest version,support keys for different car brands. v8/x6 key cutting machine user manual Language :English + Italian + Portuguese + Spanish / Turkish + English V8/X6 key Cutting Machine user instruction display in pictures: What situation you can make keys with this V8/X6 key cutter? 1) You have the original key and make a new key: When you start this machine, you will see the menu, just follow...
0 Comments | Posted By
4
This is a user manual for BMW Turbo Decoder HU92 at obd2express. How to use Turbo Decoder HU92 for BMW Open the gate (pull it out) before you start working with HU92 decoder The Turbo wheel (last wheel) must be all the way to the LEFT Reset all 8 pins to position 0, 4pins on each side of the tool (that is, push the pins all the way DOWN) Resetting complete Every time you insert the tool in the lock...
0 Comments | Posted By